Kimmy’s Garage would like to feature Michael and Keith Ciborowski on today’s blog!
Racing has been in Keith’s blood from an early age, when his father Michael would bring him to all kinds of races growing up. “Dad brought me all over the place racing as a kid and after a few bolt on upgrades I got the itch bad. That snowballed into what it is now. A 7 second turbo coyote ’03 cobra” Keith states.
Keith has a 2003 Mustang Cobra, bought in 2013. “I always loved the dark shadow grey ’03 Cobras, so when the time was right I bought one. It took me about 3 years to build it, with the help of dad” says Keith. This past year was the first year they’ve had it done. Keith went a best of 7.57 @187mph this year in street trim. Finished runner up at NMRA Bowling Green in the Turbo Coyote Shootout and made it to the Semi-Finals in the King of the 4V class at ModNationals!
Keith talks more about the products he uses, “I have Aerospace brakes on all 4 corners of this car and I love them. I originally bought the front kit for the ’94-04 cars, but later decided to switch to a foxbody setup to utilize the Aerospace hubs. When I switched to the foxbody front spindles, I used Racecraft drop spindles and was in need of them to be drilled and tapped and caliper brackets made for them. I shipped the spindles to you guys and within a week received them back with caliper brackets and all the hardware I needed to bolt them right on, customer service has been A+ for me!”
The original front Aerospace brakes Keith purchased for the car wound up on a project car of him and his Dad’s. An 83’ Mercury Capri that they coyote swapped with the stock motor out of his 2014 GT. The Capri utilizes Aerospace components brakes on all four corners as well.
Michael’s car is a 2014 GT which he purchased off Craigslist in 2014 from a guy who won the car in a raffle! The car had 400 miles when he brought it home. Slowly his car transformed into a track car, with his goals being set on the new NMRA Limited Street category. In the winter of 2017/2018 they swapped out the stock motor for an RGR built longblock and a variety of go-fast goodies in order to compete in Limited Street. His car also had Aerospace Components brakes on all 4 corners.
Their goal for the 2018 season was to finish in the top 10 in points. After struggling with new setup bugs the first 3 races and dropping the motor back into the car at 11:00pm, the Monday night before Ohio, they found ourselves in the #1 qualifier spot and ultimately in the winners circle at the Ohio event. Joliet saw them qualify 2nd and finish runner up!
“Coming into Bowling Green, we had no idea we could steal the championship, however working our way through eliminations, we came out of Bowling Green with the event win and the 2018 NMRA Limited Street World Champion. 2018 was extremely good to us, all the hard work, time and energy paid off in a big way. And it couldn’t have been done without the support of Aerospace and everyone that has had a hand in both our racing programs” says Keith and Michael,
We look forward now to the 2019 racing season. The first NMRA race is February 28th – March 3rd at Bradenton Motorsports Park,Florida. We’re hoping to grab our win there and celebrate in the Aerospace Components winner’s circle once again!
Kimmy’s Garage would like to feature Mike Bagley on today’s blog!
Mike Bagley began his powerful racing career in the early 1980’s. Through the years, his prized possessions included a ’67 GTO, ’68 Camaro, ’68 Chevelle and a 1969 Alston Chassis Camaro. With each car, Mike has taken it to the next level. Specifically, his ’69 Camaro achieved a track championship @ Bunker Hill Drag strip in the Super Pro Class and an even bigger win for the Championship at the 1992 NHRA Division 3 Super Pro Championship at Indianapolis Raceway Park. Later in the 90’s, he purchased a record holding A/ED rolling dragster, in which Mike set a Blown BBC 502 cubic inch engine for a power plant which ran in the low to mid 4 seconds in the 1/8 mile.
Mike and his team began running the Jegs Super Quick Series in 2000 and have been running the series ever since. They have raced in a few NHRA Division 3 Top Dragster events and have achieved great success with it! Running the Jegs Super Quick series brought the team incredible results over the last 17 years — with multiple Super Quick Shootout Titles and Jegs Super Quick wins, as well as multiple Top Ten finishes through out the years.
In December of 2017, Mike decided to sell his Dragster and purchased a ’63 Split Window Corvette, which at the time was only a chassis and body. Over the following six months, the chassis, interior, and body were professionally completed and then it was onto the paint shop for a top notch House of Color Cobalt Blue finish.
Mike received the car back less motor & transmission. Mike’s Crew Chief, Todd Hill, assisted with the installation of the final components of the Vette, which also included Aerospace Components Lightweight Powerglide Shifter & Shifter Cable Bell Crank, both of which are top of the line products!
“The installation of the Aerospace Components products were easy to follow with great detailed instructions!”, Mike shared.
For 2019, Mike will be using Aerospace Components’ Crank Trigger to assist the MSD grid being installed. The Vette has shown consistency in the short period of time they’ve been running it and — with the superior parts from Aerospace Components — Mike and his team look forward to a successful 2019 full season running in the Top Sportsman & Jegs Super Quick & Quick 8 series!
Mike would like to thank all who support Bagley & Hill Motorsports: including Aerospace Components, Executive Airport Limo Service and special shout out to Mike’s crew chief “Todd Hill” and Mindy Sikora, who keeps the team running at top speed!
Kimmy’s Garage would like to feature Bryan Norman on today’s blog!
Even with the summertime, inclement weather, Bryan Norman continued to pursue yet another fantastic start to his racing season.
Bryan’s first race was in late April at his local track, Capital Raceway in Maryland. He took his Mustang out, which was also it’s first time on the track since installing Aerospace Component’s vacuum pump. “The pump works great and is making the most vacuum it ever has!”, mentioned Bryan.
Bryan entered his Mustang in the Top Bulb and Bottom Bulb categories that day and ultimately won the Bottom Bulb. In the same weekend, he made it to the quarter finals in the Top Bulb, so overall it was a successful first weekend of racing.
After Bryan stopped over at Galot Motorsports Park for the K&N Spring Fling, the inclement weather made it’s way back to the northeast, which gave him a chance to analyze his dragster; including an update to the ignition with the new MSD Grid.
He then headed back to his local track to test out the new updates on his car. A .003 red light in the semi finals brought his day to a close, but that didn’t dampen Bryan’s spirit.
More recently, Bryan took to the track with his first pass at 135 mph at 5.09. After tweaking his Mustang after the first pass, the car cranked it up a notch to 141 mph at 4.91. He further implemented a converter change, which landed him at 141.5 mph at 4.88. Bryan decided to wrap up the weekend with a nice standing in the quarter finals.
The latest update for Bryan’s Mustang includes changing the 3.90 ring / pinion for a 4.30, ultimately helping with his RPM range and landing him in his 4.70’s goal. Bryan is eager to take it out for another local race as well as The Triple Crown at Maryland International Raceway!
Best of luck to you, Bryan!
UPDATE: The New Camaro Rear Kits have been designed and manufactured. They’re currently in stock! Ryan has the first set; check out the photos below!
Also, check out the newest Kimmy’s Garage video below featuring this new product! Be sure to check back for more footage of Ryan racing at the track with the new brake kits installed.
Kimmy’s Garage would like to feature Ryan Stevens on today’s blog!
Ryan is currently in the process of making his car more efficient with lighter components, like Aerospace Components brakes, on the rear.
“We really love the front brakes for the 10-15 and the custom 2016 sets Aerospace Components built for us.”
Although Ryan doesn’t have any races planned until a track rental in November at Cecil in Maryland, his car is ‘under the knife’ for basic weight loss modifications; possibly including rear drag brakes, Ceramic bearing hubs if available, electric water pump, vacuum pump, and perhaps some lighter wheels. With his current engine and power train, he believes the car is maxed on power, so the efficiency and weight are what he’s targeting over the upcoming months.
Here are the current specifications on Ryan’s Camaro:
2010: Ls3, Stock Bottom End, All Motor, Gwatney Performance Heads and Cam, cid intake
Th400 trans, circle d converter, gm3.91 gears
Weld Wheels, MT275 pro tires, and Aerospace Components front brakes (vented street rotors)
“Aerospace has been a nice addition to the family of components we use on our personal, and customer builds. You guys have been very receptive to building new products to help accommodate our needs. We are very passionate about what we do, and we try to choose the right components to give us every opportunity to succeed. We also have a great team of guys that help us accomplish what we do.”
Aerospace Components is currently creating Rear Kit for his 2016 Camaro. Check out the photos below!
The lightweight brakes on Ryan’s car have not only been helpful for decreasing elapsed times, but also providing excellent stopping power while retaining great street-ability for driving the car daily! “Fitment was awesome, they clear most every wheel imaginable with ease, and they look as good as they perform”, Ryan mentioned. In his quest for performance, light weight yet durable components are a must!
Ryan is eager to see how future products can help take his car to the next level and separate itself from the pack!
*UPDATE* The Pony Does It Again!! @ ModNationals, November 2018
Team Aerospace Racer Yandro Ulloa and his “Minion” are champions once again! He ran 7.92 @ 180 with a T-56 transmission, on full UPR suspension, with Aerospace Billet Aluminum Brakes all around! Way to go Yandro!! First Manual Trans Mustang in the 7s!
*Video and Photos courtesy of Yandro Ulloa*
Kimmy’s Garage would like to feature Yandro Ulloa on today’s blog!
Setting the manual-trans record was never something Ulloa had ever considered. His original goal when he built this car was to go 9.99 but he got there quicker than expected! Ulloa decided to make the 12 hour drive to Bowling Green, KY for an NMRA event and went 8.98 when he knew his team had something special. They continued to tweak and tune which lead to a 8.52 at 170 test pass at Bradenton then returned to the lanes to make the legendary 8.47 @ 169 pass. Ulloa’s next goal is to be in the 7s before the end of the year and be the fastest stick US domestic car!
Features of the 1998 SVT Cobra Mustang:
4.6L Mod Motor from Ford
Original stock block, crank, heads and intake (all original from this 20 year old car)
Aerospace Components brakes, made the car lighter and safer!
“Extremely sharp looking pieces that don’t only look good but work as good as they look!” says Ulloa of his Aerospace Components racing parts.
Manley rods, JE custom Pistons by Levin Motorsports Specs, Comp cams custom grind by Levin powered by twin Borg warner turbos S364.
Strange axles, spool, 1350 rear drive shaft yoke, c clip eliminator kit.
AEM infinity controls the power.
Power is being transferred through McLeod’s RXT1200, ARP Hardware Everywhere hold this thing together, Injector Dynamics send fuel, with a full Fore Innovations Fuel System custom by Levin Motorsports, Mickey Thompson tires have NEVER failed me either!
Transmission is a T56 Magnum from RPM.
- The UPR light weight but very durable parts are great and it wouldn’t have been possible to run as well as I have. These parts have been on my car for almost 2 years now getting beat on with zero signs of stress.
- High Revolution Fabrication and NXS Racing in Clearwater,Fl have been with me since the beginning, from setting pinion angle to fully built 8.8 custom rear end.
Ulloa states of his record breaking pass, “it felt like any other pass, fighting for my life making sure I don’t miss a gear never looking at speedometer so I had no clue of the speed till I got my ticket. I granny shifted the whole way down afraid something would go wrong with trany, but I’ll have it refreshed and inspected to make sure its ready for the next step!”
“I’m just an AC guy that loves going down the track, and I want to make the mustang community proud with Original Ford Motors. This is really a dream come true and a VERY humbling experience with 1000s of people saying supportive things and enjoying this with me!” says Ulloa.
Ulloa recently visited Kimmy’s Garage and we are very excited to have him as part of our Aerospace Components Team!!
Marvin’s racing career started 7 years ago, after he purchased his Mustang in March 2011. Marvin’s first NMRA event was at Joliet, IL in 2011, where he ran in the True Street class.
In 2012, Marvin decided to take it up a notch and run a partial schedule in NMRA Super Stang for points. He found himself on a roll, with his very first event in Atlanta 2012 where he made it to the semifinals.
Fast forward to this 2018 season with the NMRA, he’s won several events and is enjoying every moment of victory. Marvin was also a runner up in Joliet. Marvin has enjoyed partnering with various companies when it comes to sponsorships — including Stifflers, Brenspeed, Billet Specialties — but one of his favorite relationships and feature of his prized car is the Aerospace Components brake system.
Marvin installed the Aerospace Components brake system in January 2016. “The fit was perfect and installation was easy. Their brakes perform above expectations, and I dropped over one tenth off my ET after the install. They have excellent stopping and holding power, with superior design, style and workmanship!”, Marvin shared.
“It’s always a delightful experience every time I meet Kim and Al. The entire Aerospace Components staff is very knowledgeable and they’re willing to help with any technical or product questions.”
More recently, Marvin was crowned Champion in the SuperStang class at the NMRA All World Finals in Bowling Green, KY! Check out some photos below — congratulations to Marvin and his team for an incredible racing season!
Kimmy’s Garage would like to feature Donnie Edmonds in today’s blog!
Donnie Edmonds’ car, which has been cleverly named “Big Bertha”, is a 1969 Chevelle SS 396. Donnie’s been racing for most of his life, and this 6th generation Chevelle has been a work in progress since fall of 2013. Bertha is a solid, all original panel car and has had only one repaint in Dark Red Mica. She has a Extreme Automatics turbo 400 trans prepared by Lonnie Diers with a Griner Billet Pro Tree trans brake, and Coan and EXA billet aluminum goodies inside.
Donnie updated Bertha in December 2016 with an Aerospace Components Vacuum Pump kit. “It looks awesome!”, Donnie shared after the new kit was installed. The following spring, Donnie was able to test out the upgrades and the difference was immediate and very noticeable. Right from the start, the car picked up in ET and MPH!
The very first time Donnie ran the car with the Aerospace Components vacuum pump on it was at the NMCA race in Bradenton 2017. “I flipped out because the car matched its best ET to date in the warm Florida air, which was around 2700 feet DA. When I ran the car at my local track the previous fall, the DA was 6 or 800 feet — so I knew we were on to something!”. Then when Donnie and his team got back from the race and were able to test at their home base; Bertha made her quickest and fastest pass ever with the 9.36 at 142 MPH.
Donnie also recently decided to upgrade Big Bertha with Aerospace Component’s hybrid Ceramic Bearings, after seeing the below Kimmy’s Garage video featuring the new product. Donnie is always on the hunt to find ways to make Bertha quicker and faster, as well as safer in any way he can. This upgrade was no exception and ultimately provided that added force as well as keeping safety at the forefront. The ceramic bearing upgrade provides faster ET’s with lighter weight overall; they’re also longer lasting and corrosion resistant!
“Personally I couldn’t be happier with the product and the people I purchased it from. The Aerospace Components team has been there any time I’ve needed any assistance. If you’ve been looking at my Facebook page for any length of time, you’ll know I don’t candy coat anything — I call ‘em as I see ‘em!”
Donnie has poured his heart and soul into his car, but it’s the unique atmosphere of racing that he also gravitates towards. “I love everything about NMCA!”, Donnie explained. “The cars, the racers and the staff make it very enjoyable for me”. So much so, that the only other race Donnie normally runs in is the Shakedown At The Summit, and a race or two at his local track: Kil-Kare in Xenia, Ohio.
Before his racing career began, Donnie worked with the Cincinnati Fire Department for 25 years and retired in 2006. He spent almost all of his career in high crime, low income areas of Cincinnati. After continuous exposure to this intense environment, he decided it was time to pursue other passions in his life. Although Donnie’s greatest enjoyment is spending time with his wife and family, his ultimate passion is continuing to make Bertha the best car she can possibly be.
“I choose to do that the hard way by making her quick and fast with no power adders. She is completely NA and I like it that way”, Donnie mentioned. He understands that anyone can make their ride quick and fast with NOS or power boosters, turbos or blowers, but getting a 3,700 lbs car to run bottom 9s on a small tire is a feat all in itself. This is a feat that Donnie is excited and ready to tackle this coming racing season!
“I truly appreciate the support that Kim, Al and the rest of the crew from Aerospace Components gives to its customers and racers in general. I would and do highly recommend their products to anyone and everyone I come across.”
We wish Donnie and the D&S Motorsports team the best of luck and we can’t wait to see you at the NMCA Summit Motorsports Park Norwalk race (August 23-26) in the Aerospace Components Winner’s Circle!
Check out these awesome videos below of Donnie demonstrating how the Aerospace Components vacuum pump improves his overall performance on Big Bertha and also shows the installation!
Introducing our new space age, ceramic bearings!
Are you running “parts store” grade steel bearings in your race car? Then you’re racing with the lowest cost bearing available and not making use of the latest technology in bearings. Ceramic Bearings offer many benefits for the racer, and the cost to upgrade is very affordable!
Some of the benefits to this upgrade include:
Faster ET’s – Ceramic bearings have 1/10th the friction of steel which means faster ET’s!
60% Lighter Weight – silicon nitrate balls weigh 50% less than steel balls of the same size. Reduce your bearing rotating weight!
Longer Life – Ceramic bearings last up to 5 times longer than steel!
Cool Run – Ceramic bearings have no micro weld adhesion between the ball bearings and races which mean lower friction, meaning they’re corrosion resistant. Ceramic also has a lower amount of thermal expansion which also reduces temperatures. Bearings run cooler and vibration levels are lower at high RPM!
Featured below are the complete vacuum pump systems with a variety of options. One kit has a stainless steel hose while the other kit has a black hose. There’s something for everyone and the choice is up to you!
Pricing starts at $199.00 for new pumps!
*Installation fee ($99) applies to used pumps sent it for upgrades
Call Aerospace Components today to place your order! 727-347-9915